Results 31 to 40 of 40
Threaded View
-
12th April 2013, 04:20 PM #1
Truck 9.700/9.701/7.902 tips & tricks (more welcome here)
If you DO want to use the 9.7** navcore (see other posts/reports about errors in this navcore) because you want to run the v910 or later Truck map (which will ONLY run on this navcore) then here are a couple of tweaks summarised below:-
Problem 1: When entering Vehicle height you can't add the . "dot" or ' foot mark eg.
if you want to add 14' 9" high, you can only enter 14' or 15' not between size.
Solution: if you set height at 14' then tap done...
it then goes to vehicle width, tap back...it goes back to vehicle height...
tap the screen anywhere but not on the keypad (this will remove the white box around the 14')
now enter 9 and then done, this will give you vehicle height of 14'9"
the same process can be done with vehicle length/height/width
Problem 2 (ONLY for the x40's): After initial boot up after a hard reset or inserting your truck card when you CAN set your vehicle dimensions, this screen/option is not available again.
Solution(s):
1. Change preferences > Planning preferences > Edit vehicle profile from there
or
2. Set a new destination and when it's all set up the last screen will tell you your vehicle profile where you can change it
Also note, if you select "car/taxi/van/other" profile you lose the option to change vehicle profile again unless you remove SD card/reboot/re-insert etc or do a factory reset THEN you have the option back.
Any other solutions/tips/tricks specifically for these 9.700/9.701/9.702 navcores can be posted/asked herebiggerdave Reviewed by biggerdave on . Truck 9.700/9.701/7.902 tips & tricks (more welcome here) If you DO want to use the 9.7** navcore (see other posts/reports about errors in this navcore) because you want to run the v910 or later Truck map (which will ONLY run on this navcore) then here are a couple of tweaks summarised below:- Problem 1: When entering Vehicle height you can't add the . "dot" or ' foot mark eg. if you want to add 14' 9" high, you can only enter 14' or 15' not between size. Solution: if you set height at 14' then tap done... it then goes to vehicle width, tap Rating: 5
SPAM HUNTER/KILLER
Please do not just post "thanks" but use the "thanks" button bottom/right or the reputation star "*" bottom/leftS i m p l e s
-
The Following 12 Users Say Thank You to biggerdave For This Useful Post:
- [ Click To Expand ]
-
Alfred_ML (29th April 2020), avci66 (20th March 2020), benpv (2nd March 2016), dkfranz (23rd May 2016), Eclipse1954 (18th October 2018), fullequipe (1st September 2016), hayg1 (28th August 2013), juan antonio (23rd May 2015), kazupp (13th April 2013), nelito77 (27th February 2016), nilude71 (25th January 2017), teschke (18th August 2019)
Similar Threads
-
Navcore Truck 9.701 (OFFICIAL version) for X20 X30 and X000
By nest0r in forum TomTom Truck and CamperReplies: 10Last Post: 1st January 2023, 04:04 PM -
Warning, truck navcores 9.700/9.701/9.702 appear to be faulty!
By biggerdave in forum TomTom Truck and CamperReplies: 74Last Post: 10th March 2017, 06:20 PM -
SE 9.700 TRUCK NAVCORES for other devices
By biggerdave in forum TomTom ArchiveReplies: 42Last Post: 5th May 2013, 05:52 PM
TomTom v1130 Maps [No Requests]
Just read post #1 Peter Admin note AND...