Results 201 to 210 of 383
-
27th September 2020, 08:52 PM #201
-
29th October 2020, 12:29 AM #202
I'm trying to install new map for VIA 120, so I choose Central and Eastern Europe, patched and updated the newest meta, but when I start my navi I see "Problem with map. I cannot use this map on my device", after that I click OK and choose again the map and I click map and see "loading map" and it takes about 1-2 mins and navi will restart automatically and show error again, what's wrong?
EDIT
Finally I could install just CENTRAL EUROPE, but I needed to change to nav3-sayville and install meta 2-3 times and reboot my navi, but after full reset I got notification that this map is not for my device, but after OK it loads it. So I can't use normal version nav3?
Is it any way to install full Europe for VIA 120 with external 4 GB (about 3.5 GB for using), maybe there is some way to delete speach for different country or something to fit Europe for my internal memory?
EDIT2
I wanted to install post code for UK, but button for install is not available, why?Last edited by SkuterPL; 29th October 2020 at 02:12 AM.
-
8th November 2020, 09:52 PM #203
Adding the Nav3 devices is a SUPER JOB!!!!
-
14th November 2020, 11:28 AM #204
Hello, tomtom go 1000 live after update does not start anymore. Startup screen remains hanging. Do you know why?
'"unable to load page-problem occorrud white loading'"remains in writing.
This happened after navcore update. Is it possible tha I updated the wrong navcore? I did this by myself, so it wasn’t automatically.
It doesn’t connect to my laptop and also not to TomTom mydrive. And I can’t do anything. What can be the problem?
Thankyou in advance
Last edited by oxili; 14th November 2020 at 05:57 PM.
-
15th November 2020, 10:00 PM #205
-
The Following 1 Users Say Thank You to simba For This Useful Post:
- [ Click To Expand ]
-
oxili (16th November 2020)
-
16th November 2020, 12:36 AM #206
Hello Simba, 4.3” so 5” actually.
I did a hardreset and conected to TomTom mydrive. It is telling it will reset to fabrics but I’m waiting almost an hour. Do you have any other ideas what to do?
-
16th November 2020, 01:50 AM #207
-
The Following 1 Users Say Thank You to Xius27 For This Useful Post:
- [ Click To Expand ]
-
oxili (16th November 2020)
-
16th November 2020, 02:21 AM #208
Yes, I've been waiting for hours but it stays on the last screen and I'm still waiting.
-
16th November 2020, 03:36 AM #209
It stays as in the photo and TTActivador or MyDrive connect does not recognize it ??? if TTActivador recognizes it, install your navcore format .ttpkg
In short, normal boot stays on the white screen and boot recovery mode as in the last photo
The same or similar happened to me, I did several things that I do not remember exactly, one of the things I did disassemble and disconnect the battery for 15/20 minutes,
At one point I did recognize it TTActivator installed its navcore, for a 4.3 "screen it would be 12.075.3065980.84
regards
-
The Following 1 Users Say Thank You to simba For This Useful Post:
- [ Click To Expand ]
-
oxili (16th November 2020)
-
16th November 2020, 04:03 AM #210
Just recognize it with recovery mode and it says you can't do navcore with recovery mode. I accidentally did navcore 12.075.3065980.94 then this problem started. I'll take out the battery and try it later. Thank you.
Garmin Cyclops Safety Cameras -...
Garmin Cyclops May-04-8-2024 ...