Results 1 to 4 of 4
-
21st June 2020, 01:39 AM #1
Reflections on Camper Map in Go Live 1005
Regards
I am immense in the installation of a Camper map in my Live 1005 (BT), I want to put this map in the IM of the TT ... To date I can not get the map to work alone.
I tell you my experiences, I start from an original nacvore -12.075.3065980.74- and an obsolete map of Europe Zone 3 -v. 925- (all patches are done with the TTActivator)
These patches I do as follows (introduction):
0.- I delete IM maps
1.- I update META
2.- I install the NAV that I want
3.- The TT restarts
4.- It tells me that there are no maps in the TT
5.- Download map
6.- I upload META to the map
7.- Restart the TT with the TTActivator
8.- I update QuickGPSFix
9.- If I want to install another map, I start from section 5
I have installed the patch to normal navcore and I have installed the Iberia map and the Camper map, the navigation is correct, and the "Go to" option works 100% (the vehicle change and resize vehicle options work 100%)
I have installed the patch to normal navcore and I have only installed the Camper map, the navigation is correct, but when it comes to putting a route ("Go to", we are going to call it destination 1), I put a destination in the TT and this will be blocks, restarts, puts me writing route instructions; and it is a closed loop, it restarts and starts asking me to select the map, I select it and restart it again (the options of changing the vehicle and resizing vehicles works 100%),
As I knew that with two maps it worked for me, I go to section 5 of the introduction and install the Iberia map, to this I put "Go to" destination 2, and I see that now destination 1 is going to me (the TT is not blocked) and when I make the change to the Iberia map, it also goes to destination 2
I have installed the patch to navcore truck and I have only installed the Camper map, the navigation is correct, but when it comes to putting a route ("Go to", we are going to call it destination 1), I put a destination in the TT and this will be blocks, restarts, puts me writing route instructions; and it is a closed loop, it restarts and starts asking me to select the map, I select it and restart it again (the options of changing the vehicle and resizing vehicles works 100%),
As I knew that with two maps it worked for me, I go to section 5 of the introduction and install the Iberia map, to this I put "Go to" destination 2, and I see that now destination 1 is going to me (the TT is not blocked) and when I make the change to the Iberia map, it also goes to destination 2
I have installed the patch to navcore truck and I have installed the Iberia map and the Camper map, the navigation is correct, and the "Go to" option works 100% (the vehicle change and resize vehicle options work 100%) , the only difference that I see, that here, gives me the option to choose the truck vehicle, which in the camper it does not give me (as is normal)
Any suggestions to make the Camper map work ???
THXPoteo_Roke Reviewed by Poteo_Roke on . Reflections on Camper Map in Go Live 1005 Regards I am immense in the installation of a Camper map in my Live 1005 (BT), I want to put this map in the IM of the TT ... To date I can not get the map to work alone. I tell you my experiences, I start from an original nacvore -12.075.3065980.74- and an obsolete map of Europe Zone 3 -v. 925- (all patches are done with the TTActivator) These patches I do as follows (introduction): Rating: 5Last edited by Poteo_Roke; 21st June 2020 at 02:44 AM.
-
The Following 1 Users Say Thank You to Poteo_Roke For This Useful Post:
- [ Click To Expand ]
-
Orni (21st June 2020)
-
21st June 2020, 05:48 AM #2
-
The Following 2 Users Say Thank You to master131 For This Useful Post:
- [ Click To Expand ]
-
Orni (21st June 2020), Poteo_Roke (21st June 2020)
-
21st June 2020, 12:43 PM #3
It is a success to do so, it works on my Live 1005 ...
On the other hand; I THINK that the pdi´s are a bit obsolete, I have found these
that are more updated, and I say more updated, because in my town there has been a parking space for about five years and other needs for motorhomes and this site (pdi) does NOT appear in the pdi´s that the camper map bringsLast edited by Poteo_Roke; 12th September 2020 at 05:02 PM.
-
The Following 4 Users Say Thank You to Poteo_Roke For This Useful Post:
- [ Click To Expand ]
-
-
21st June 2020, 04:05 PM #4
... believed that everything was going well; but now I have started to configure the pdi´s that I have in the TT, and ZAS !!!! blocking ... I will start from ZERO again and this time, I will patch as I was doing, with normal navcore, but with the map of Morocco that is smaller than the Iberia and the Camper map ...
-
The Following 1 Users Say Thank You to Poteo_Roke For This Useful Post:
- [ Click To Expand ]
-
Orni (21st June 2020)
World/Europe Speedcams from SCDB
But this is a new invention of thieves. To steal,...