You take the photo, upload it on a server, for example.
Copy the url of the photo and paste it in the post by clicking on the tag:
https://i.imgur.com/BBSc6lv.png
Printable View
You take the photo, upload it on a server, for example.
Copy the url of the photo and paste it in the post by clicking on the tag:
https://i.imgur.com/BBSc6lv.png
Thank you Xius27, I will try.
The first picture shows that I successfully installed the safetycams.
https://i.postimg.cc/V676GzXB/20200608-184529-A.jpg
https://i.postimg.cc/W12yjZKn/20200610-103210-A.jpg
https://i.postimg.cc/MpdFGTJ8/20200610-103421-A.jpg
As you see I was succesfully to place one map into the Internal Memory ans one map on a micro-sd card.
Both cards work well.
But I cann't get the safetycams to work.
The demo route in Holland is:
The city is called: Amersfoort
Starting point: Maatweg 1
The End : Zangvogelweg 2
That is well configured. I think that the radars you indicate are not at the base of tt
You must proceed as you have done for the images but using the image path with the extension that has been created, in your case "jpg" using the [ img ] [ /img ] tags (no space) example with the code:
You remove the spaces and it looks like this
https://i.postimg.cc/mhHjMJ8V/20200610-103421.jpg
To me, that route that it marks marks only 2 traffic light radars, see if that category is enabled.
https://i.imgur.com/wylUyOs.png
https://i.imgur.com/nWSxtLA.png
@Orni,
You asked me: To me, that route that it marks marks only 2 traffic light radars, see if that category is enabled.
Look at the 2 pictures below.
https://i.postimg.cc/kGnH4dHZ/Flitsers-AA.jpg
https://i.postimg.cc/WzXHqHL4/Flitsers-BB.jpg
@Xius27,
I also have an Tom Tom Go 940 ( NAV2)
Yesterday I downloaded the safetycams with the tool TTActivator to my Tom Tom Go 940.
In DEMO I did ride the same route in Amersfoort.
Now I got a warning when I approached a safetycam. Look at the picture below.
https://i.postimg.cc/mZwqntzG/TT940B.jpg
So I think that I'm doing something wrong, but I don't know what.:dj:
@Orni,
The two pictures in your reply #14 were also taken from an NAV3 Tom Tom?
https://i.imgur.com/wylUyOs.png
If that's the case, I'll do something wrong, just what?
Yes, nav3 TT Start 25
Can someone tell me what you did exactly, after completed installation successfully of the safetycams / speed camera's?
Which actions did you perform exactly, so that the speed cameras were effective on your nav3 device?
@Orni,
In one of the pictures in your reply #6 I see something in the top right corner.
https://i.postimg.cc/brKxsxC5/Flitspaal-01.png
If someone has properly installed and activated the safety and speedcams on his NAV3 system,
does this appear in the top right corner?
When I take a picture of my screen ( Start 25 ) there is nothing to see in
the top right corner.
https://i.postimg.cc/c1jM9Wxc/Flitspaal-02.png
This means that I didn't do the activation properly?
When I used upload_ttkpg I got the black screen which said :
Installation completed succesfully.
https://i.postimg.cc/V676GzXB/20200608-184529-A.jpg
What do you do next to make the activation succesfully?
My cameras are expired, the message in the upper right corner says "cameras not updated"
I updated now
https://i.imgur.com/NoqwHo3.png
There is no message above
https://i.imgur.com/xcnGhpK.png
I edit
After installing the update it no longer warns of radars.
Installed the radars on a map of the card already works again.
At the moment the only solution is to install the radars on the card as well.
I edit again
After installing the radars on the card map and performing the route demo, the radars have sounded. I have removed the card with the map and the radars that I had installed leaving only the map of internal memory now the notices work again.
Installing the radars in the internal memory has activated the warnings again.